RESUMEN
This study aims to investigate the effects of introducing a 50/50 mixture of silica and magnesium oxide nanoparticles (SNP + MgONP) to the viscosity of Al-Ahdab crude oil (Iraq) at varied concentrations and temperatures. It is observed that the viscosity value drops from 38.49 to 7.8 cP. The highest degree of viscosity reduction is measured to be 56.91% at the maximum temperature of 50 °C and the greatest concentration of 0.4 wt% SM4. The Bingham model can be used to classify the behavior of the crude oil before the Nano-mixture is added. The liquid behavior grew closer to Newtonian behavior once the Nano-mixture was added. Along with a rise in plastic and effective viscosity values, the yield stress value decreases as the concentration of the Nano-mixture increases. The numerical data demonstrate that when the volume proportion of nanoparticles increases, the pressure distribution decreases. Furthermore, as the nanoparticle volume fraction increases, the drag decrease would also increase. SM4 obtains a maximum drag reduction of 53.17%. It is discovered that the sample SM4 has a maximum flow rate increase of 2.408%. Because they reduce the viscosity of crude oil, nanoparticles also reduce the friction factor ratio.
RESUMEN
In recent years, in order to obtain improved mechanical, thermal, electrical and barrier/transport properties, aligned carbonaceous nanomaterials/polymer nanocomposite films have been receiving growing attention. Correspondingly, the edge oxidized graphene oxide (EOGO) nanoplatelets alignment influence on the structure of the polyethersulfone (PES) membrane films for potential applications in water treatment field has been investigated. Aligned GO/PES nanocomposite membrane films were prepared by non-solvent phase inversion technique after the starting sol phase was preliminarily exposed to high electric fields (50 kV m-1). Either AC (100, 1000 Hz) or DC mode electric fields were alternatively employed, and the results from both vertical and horizontal field configurations were investigated for structural and morphological comparison. Both XRD, FTIR-ATR, EIS, SEM, TEM and tensile strength analyses were applied in order to characterize the films. The microscopic analyses results have demonstrated successful GO/PES nanocomposite formation and alignment of GO nanoplatelets with the field direction in the matrix at low to moderate (0.02-0.1% wt) GO loadings where the flakes were dispersed and exfoliated sufficiently. However, at higher loading levels (1 and 2% wt) the nanoplateles were mostly agglomerated and the big flakes consisting of irregular plates could not orient their axis parallel to the electric field at the employed field strengths. The results suggest a more effective role of higher frequencies (1000 Hz versus 100 Hz) electric field for alignment of GO nanoplatelets. Simple tensile tests have also similarly confirmed GO alignment under the electric fields at both low (0.1% wt) and moderately high (0.5% wt) GO contents. The tensile strength improvement of the horizontal field processed PES/GO nanocomposite up to 24% compared to its vertical field processed counterpart could be accounted as a proof of the successful alignment of the nanoplatelets. However, EIS results unveiled that non-solvent phase inversion casting method, in its general form, may not be a suitable method for producing materials with tailored properties, due to its random and uncontrollable pore forming mechanism.
RESUMEN
The purpose of this study was to investigate the effect of process parameters including silica nanoparticle (NP) concentration, biosurfactant (BS) concentration, and salinity as well as their synergistic effects on oil recovery in simultaneous flooding. Additionally, the effect of NP morphology (in the BS-NP solution) on oil recovery was investigated in this research. Micromodel flooding tests were designed with a central composite design (CCD) and carried out using BS and spherical silica NPs. The results showed that there is a positive synergistic effect between BS and silica NPs to shift the wettability to the water-wet condition and decrease interfacial tension (IFT), resulting in improved oil recovery. Indeed, the maximum oil recovery was obtained at an optimum salt concentration. Several micromodel tests were then carried out with BS and different-shaped NPs at the optimum point predicted by a mathematical model to study the effect of NP morphology on oil recovery. The results showed that minimum IFT of 1.85 mN m-1 and the most reduction in the glass contact angle of 92.8% could be achieved by the BS-spherical NP solution as compared to those of the BS-non spherical NP solutions, which led to the highest oil recovery of 53.4%. The better performance of spherical NPs was attributed to the higher uniformity, which resulted in better distribution and more effective interactions with crude oil components. The results of core flooding tests showed that the BS-spherical NP solution yielded 26.1% final oil recovery after brine flooding. In addition, the BS-NP solution was more effective in wettability alteration of an oil-wet carbonate rock compared with the BS solution. It was deduced that the main mechanisms involved in oil recovery improvement were wettability alteration to the water-wet state, IFT reduction, and mobility ratio improvement.
RESUMEN
In this study, a glycolipid type of biosurfactant (BS) was produced, its characteristics were evaluated and several flooding tests were conducted in a micromodel to investigate its potential for enhancing oil recovery. A rhamnolipid BS producer strain was identified as a bacterium belonging to the genus Pseudomonas aeruginosa. This BS showed good stability at temperatures of 40-121 °C, pH values of 3-10 and salinity up to 10% (w/v) NaCl which is important in Microbial Enhanced Oil Recovery (MEOR). The rhamnolipid decreased the surface tension of water from 72 to 28.1 mN m-1 with a critical micelle concentration of 120 ppm. Thin layer chromatography, FTIR spectroscopy, 1H-NMR and 13C-NMR spectroscopy revealed the glycolipid structure of the BS. Response surface methodology was applied to optimize BS production. Several micromodel flooding tests were conducted to study the capability of the produced rhamnolipid in enhanced oil recovery for the first time. An oil recovery factor of 43% was obtained at 120 ppm of BS solution whereas the recovery factor obtained for water flooding was 16%. Contact angle measurements showed that BS solutions altered the wettability of a glass surface from oil wet to a strongly water wet state. Also the results illustrated that all BS solutions were impressive in microbial enhanced oil recovery (MEOR) and using the produced BS a considerable amount of trapped oil can be extracted due to interfacial tension reduction, wettability alteration towards water wet conditions and improving the mobility ratio.
RESUMEN
An N-butylamine functionalized graphene oxide nanolayer was synthesized and characterized by ultraviolet (UV)-visible spectrometry, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy. Detection of iron(III) based on photoluminescence spectroscopy was investigated. The N-butylamine functionalized graphene oxide was shown to specifically interact with iron (III), compared with other cationic trace elements including potassium (I), sodium (I), calcium (II), chromium (III), zinc (II), cobalt (II), copper (II), magnesium (II), manganese (II), and molybdenum (VI). The quenching effect of iron (III) on the luminescence emission of N-butylamine functionalized graphene oxide layer was used to detect iron (III). The limit of detection (2.8 × 10(-6) M) and limit of quantitation (2.9 × 10(-5) M) were obtained under optimal conditions.
